Another Review on the Installation of the MOSS Master Cylinder

Photo for Another Review on the Installation of the MOSS Master Cylinder

I had the opportunity recently to evaluate one the new Moss Motors branded MGA 1600 master cylinders, specifically their part #180-751.

The vehicle that this M/C was going in is a 1962 MkII MGA. The existing M/C was starting to seep a bit on the brake side. Time for either a kit or a replacement unit. I chose to go replacement since the installed unit had been there a while. Honing and installing a kit can work sometimes, but this way, I would be sure.

At first glance, the unit was identical to the OE one. Actually, some of the casting marks were a bit crisper on the new one. It would be nice is Moss would be able to reproduce the original style filler cap, rather than using the plastic one, but maybe that will happen someday.

After the first brief inspection, I was actually a bit dismayed. Rather than using the correct fillister head screw to hold on the top and front covers, Moss chose to go with some metric hex head bolts. After a brief flurry of e-mails to Moss, I was very pleased to learn that the correct fillister head bolts, which Moss sells as #323-500, actually fit, and fit well, in the M/C. The supplied metrics internal tooth star washers are a bit tight, so I replaced them with similar ones, but that fit the 1/4-28 fillister head screws.

I am sure Moss feels they have a valid reason to go with the metrics, but it would be a whole lot easier if they either install them, included 7 in the box, or at least noted in the catalog and website that the customer might prefer the fillister head screws.

Metric Hex Head BoltsMetric Hex Head Bolts

The installation and swap went quite easily. Removing the clevis pins from the push rods sometimes takes a bit more dexterity than I would like to admit and removing the pipe and banjo bolt from the rear of the MC is always a bit tedious, and sometime a matter of 'holding your mouth right', but if you understand it is awkward up front, then you won't be disappointed.

Prior to installing the new unit, I 'bench bled' it. This allows the installer to actually get hydraulic fluid, in this case silicone, into the bores of the M/C and prime them. Upon installation, this makes the bleeding process very straightforward.

Bench BleedingBench Bleeding

After the bench bleed, installation was quite easy. I replaced the copper washers that are used at the banjo bolt and adaptor on the clutch side. I threaded in the brake and clutch pipes loosely. It is easier to line them up while the M/C can be moved a bit to help with the alignment. Once snugged down, I reinstalled the two push rods into the front of the M/C and then moved the M/C a bit to install the two bolts securing the M/C to it's' bracket. Then I reach around back and tighten the rear fittings. Reinstalling the clevis pins and cotter pins always looks easier than it is, at least for me.

To make the system bleeding process a bit easier, I have modified an Eezibleed Kit that Moss sells. For me, it seems to work best at about 7 PSI of pressure. The kit is designed to hook up to a tire to provide the air pressure, so you need to drop the tire down to a lower pressure, and typically add a little air frequently. I cheated and add a mini regulator to the system. I can now attach the Eezibleed directly to an air hose from my compressor and take all of the time I need to bleed the system. Just a random thought here but if the Eezibleed folks can come up with a cap that fits the M/C, maybe they should provide new caps, with out the big hole, as an alternative to the current big, ugly, plastic cap.

EezibleedEezibleed

Since the system, and particularly the clutch slave cylinder already was functional and had fluid in it, and since the new M/C was bench bled, bleeding the entire system was very easy. As the manual suggests, you start at the bleeder farthest from the M/C and work in. The Eezibleed takes care of the fluid level. Remove the air line, then the Eezibleed, place the cap on the M/C, and you are done.

Progress report. There were initially some issues with the pistons return correctly in the bores. I believe Moss has addressed that issue. This unit has functioned as designed for about 500 miles without any issues. Other than fillister head screws and the plastic filler cap, the Moss M/C seems to be a perfect replacement for the OE M/C.

Stay current with NAMGAR, MGA news, and more:   Subscribe to updates by email

Reader Comments (1)

Picture of Joe Schandl
Joe Schandl (New Smyrna Beach, FL)
on April 30, 2012 2:41pm
very good article

Tell us what you think

We welcome your feedback! Enter your information below to add a new comment.

Are you a NAMGAR member? Login before posting your comment

Name: (required)

Email: (required, will not be published)

Location:

Your Website Address / URL:

Your Comment: (required)

Remember my personal information for next time

Notify me of follow-up comments via email

Enter the word you see below:

Comments may be held for moderation. If your comment does not appear immediately, do not repost. We reserve the right to remove any inappropriate or off-topic comments. Want others to know who you are? Register a Gravatar.

Your privacy is important to us. Read our privacy policy

Last updated on November 11, 2010.

Related Posts Plugin for WordPress, Blogger...